LED

Loading...
Yellow 5mm water clear LED
Category:LED
Release date:2019-01-21 11:01:37
 
Features
․High luminous power.
․Yellow color.
․Bulk, available taped on reel.
․ESD-withstand voltage: up to 4KV
․The product itself will remain within RoHS compliant version.
 
Descriptions
․The series is designed for application required high luminous intensity.
․The phosphor filled in GaAsP/GaP chip to ideal white.
 
Device Selection Guide
LED Part No. Chip Material Lens Color
Y5012UC GaAsP/GaP Water clear
Package Dimensions

Absolute Maximum Ratings (Ta=25) 
Parameter Symbol Rating Unit
Continuous Forward Current  IF 30  mA
Peak Forward Current IFP 1 A
Reverse Voltage VR 5 V
Operating Temperature Topr -25 ~ +85
Storage Temperature Tstg  -25 ~ +85
Soldering Temperature Tsol 260
Power Dissipation at25℃Free Air Temperature Pd 80 mW
Zener Reverse Current Iz 100 mA

Notes: *1:IFP Conditions--Pulse Width≦100μs and Duty≦1%.
*2:Soldering time≦5 seconds.
Electro-Optical Characteristics (Ta=25)
Parameter Symbol Condition Min Typ Max Unit
Forward VF IF=20mA 1.8 -- 2.3 V
Zener Voltage Vz Iz=5mA 5.2 -- -- V
Reverse Current IR VR=5V -- -- 5 μA
Luminous Intensity Iv IF=20mA 8000   10000 mcd
View Angle 2θ1/2 IF=20mA -- 15 -- deg
Peak Wavelength λp IF=20mA 587 -- 590 nm
 
Packing Quantity Specification
1. 1000PCS/Bag
Notes
1. Lead Forming
  1. During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
  2. Lead forming should be done before soldering.
  3. Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it may break the LEDs.
  4. Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may cause failure of the LEDs.
  5. When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs.
2. Storage
  1. The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from XingHui and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material.
  2. Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur.
3. Soldering
  1. Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is recommended.
  2. Recommended soldering conditions:
 
Hand Soldering DIP Soldering
Temp. at tip of iron 300℃ Max. (60W Max.) Preheat temp. 100℃ Max. (60 sec Max.)
Soldering time 3 sec Max. Bath temp. & time 260 Max., 5 sec Max
Distance 3mm Min.(From solder joint to epoxy bulb) Distance 3mm Min. (From solder joint to epoxy bulb)
.
Remark
1. Above specification may be changed without notice. XingHui will reserve authority on material change for above specification.
2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. XingHui assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets.
3. These specification sheets include materials protected under copyright of XingHui company. Please don’t reproduce or cause anyone to reproduce them without XingHui’s consent.




Copyright © 2018 Ningbo ANYO Imp.& Exp.CO.,LTD(宁波安甬进出口有限公司) All Rights Reserved 浙ICP备18014421号 by:e7cn.net

浙公网安备33021202001960号

+86-574-56807757
info@anyoltd.com